SP101 .357mag technique question.

S

Sweet Shooter

New member
It's a 3 inch barrel with fixed sights. I could not shoot to the sights with 357 and was hitting about 6 inches low and to the left. I was worried that this gun was too small for full house 357s. After adjusting my technique to keep my pinky off the grip—which is too a grip small anyway—and also inserting my trigger finger further to just onto the second pad, I can now keep about 5 inch left/right at 15 yards with SA.

I'm locking my right hand thumb down with my left. Is there a secret to tightening the group. I kind of was hoping to be able to shoot a 2 or 3 inch groups at that distance SA. Am I expecting too much. Not exactly a cheep round to practice with. Any tips? I'm not much of a revolver shooter but want to become better as I am going to get my concealed carry permit and this particular course has a range component. The SP101 is the only one I have small enough.

-SS-
 
I don't know this gun for sure, but low is usually too much grip or flinch. Try a lighter grip.

I think your right/left could be trigger finger. Try putting the first knuckle on the trigger and pulling straight back. Watching the sights jump in dry fire could help you work out both these issues.

Focus on where the sight jumps as the hammer releases. It really shouldn't move at all. Until hammer momentum knocks it straight down slightly. That should feel a few milliseconds after the sear release.
 
What weight of 357 ammo? Most fixed sight 357's are regulated for 158 Grain bullets. How much low are you shooting? The standard sight in is 25 yards. A revolver is more difficult to shoot well than a good auto, try some dry firing.
 
You know maybe it was 25 yards... didn't seem very far. The ammo was 125gr.
Thanks for the help and heads up... both you guys.
-SS-
 
New Gunitis

You may be different than me, but whenever I get a new handgun, it takes a few hundred rounds for my head to get adjusted, for whatever reason. Some more experienced hand gun shooters can do amazing things, but in reality, unless you shoot a couple three hundred rounds per week for an extended period, it is tough to get a two inch group at 25 yards shooting off hand with full house 357 mag ammo.

You can dry fire that SP101 all you want, so like somebody else mentioned, that is an excellent way to practice your technique, and see what is going on with the gun while you squeeze the trigger. And another benefit is, the trigger will become a bit more smooth the more you practice.

You can google "revolver shooting technique" --here is a link I read that helped me.

http://www.backwoodshome.com/articles2/ayoob85.html

Happy shooting!
 
I have 686p from the performance shop that is the sweetest shooting revolver. trigger is great the ported barrel stops a ton of upward recoil I had a friend make a underlug weight that improves any leftover recoil .Have a great day :D
 
The SP 101 wants 158 grain in order to shoot at POA. I believe it says that in the manual. 125 grain will shoot low as you now know. Shooting left however, may be a technique problem.
 
Thank you. That I have the wrong ammo and a technique problem is good news. I was worried that the bore might be off axis from the fixed sights. How likely is it that could be the case with a 3"? Other opinions on what my expectations should be?

-SS-
 
Bore-axis/sight misalignment, while always possible, is unlikely.

I think you've gotten the advice you need to make it work for you.

I have a 3" SP101. With the right ammunition, it is quite accurate.

If you don't bring your results closer to your desires with practice, try to get someone with revolver experience to observe...

My SP101 is one of my favorites.

Best,

W
 
I consistently shot my SP101 to the left for some reason. Not that it is so much that it makes much difference at combat distances but it bugged me when I first got it. Mine is a double action only so I have always attributed it to my technique. I shoot my single actions to dead center.
 
Another thing to try is have a friend with you and have him load only 3 rounds in the chambers spaced randomly. Then safely hand you the gun to fire.
You can tell very quickly if you’re flinching or pulling the gun off target when it goes click.
One man I was helping was actually lifting the barrel when he shot. And he wouldn’t listen to me. I finally handed him the gun so that it fired the first two rounds then the next two were empty followed by a loaded.
This was a Smith L frame with 38’s. On the first empty chamber the recoil looked almost as strong as chamber that fired.
 
You're learning the hard way, why small revolvers in big calibers suck! If you want to shoot the mags, get an N frame. Mfgs should be ashamed of themselves for marketing these small guns. Shoot 38spls through your gun. It's what a gun that size was designed for.
 
Revolver1 said:
You're learning the hard way, why small revolvers in big calibers suck! If you want to shoot the mags, get an N frame. Mfgs should be ashamed of themselves for marketing these small guns. Shoot 38spls through your gun. It's what a gun that size was designed for.
Click to expand...

Not to be mean but its not the MFGs fault. In the US its always someone elses fault. I have a 3" sp101 and with 357 it is stiff but very fun to shoot. If you dont research what your buying its your fault for getting something you are not comfortable with.

The 357 in an sp101 isnt for everyone. But it isnt ouragous either and honestly many guns scare me but not this one.

To yhe OP, put as many rounds as you can theough it, try different grips and trigger pulls and i am sure it will come around!
 
I did also put hogue momogrips on mine. 24 bucks on ebay and it made a HUGE difference. A bit bigger than the factory ones, but 100x more comfortable and made 357s much nicer
 
with 357 it is stiff but very fun to shoot.
Click to expand...

+1

If Ruger has anything to be ashamed of in reference to the SP101 it's just for not making more of 'em.

It is one of the ergonomically most well-executed concepts out there.

It's honestly one of the handful of firearms I've ever used that I have literally nothing to complain about :).

W
 
You're learning the hard way, why small revolvers in big calibers suck! If you want to shoot the mags, get an N frame. Mfgs should be ashamed of themselves for marketing these small guns. Shoot 38spls through your gun. It's what a gun that size was designed for.
Click to expand...

I had to laugh. We (the shooting public) had been asking for a small 357 for years when Ruger led the way with their SP101 in the 1980's.
 
You must log in or register to reply here.
Back
Top