Off use of a tumbler

R

Roamin_Wade

Moderator
I don’t reload...yet, but I have some whole, unspent 30-06 shells that have some superficial surface corrosion on them. I’d post a pic but I still can’t figure out how to post pics with my phone. Can I put whole loaded bullets into a tumbler to polish the corrosion off of them? Also, how much time does it take to tumble-polish a load of shells? Thanks for your input...
 
Last edited:
I just posted my first pics. Downloaded google pictures and learned to crop photo. It reduces file size of pic then save smaller image. Right below post text screen is manage attachment button upload from file and it will submit with your post.
 
No I would not tumble loaded ammo. The burning rate of powder is somewhat regulated by its physical size of the granules. By tumbling the ammo the powder may become finer and affect its burning rate and thus increase the pressure when fired.
Fire the ammo and then clean the cases.
 
As wv109323 said, you don't want to tumble loaded ammo. If the surface corrosion is bad enough, wipe them with some "0000" steel wool until they look good enough to shoot.

Don
 
Hmm, I wouldn’t have thought that the powder inside the shell could break down in such a way that it would cause a dangerous pressure issue. Is it because of the high frequency vibrations that some tumblers have or just the fact that they turn and roll so long that does it? Also, if it is the frequency vibration can it be turned off so I can do this or do all tumblers have vibration that can’t be turned off? Would the media do the job alone?
 
Sure Shot Mc Gee said:
Nope! not a good idea tumbling live ammo.

A little Brasso polish sold everywhere will also remove light corrosion.
Click to expand...



Never use brasso or other polishes that contain ammonia on ammo components. Ammonia breaks down the brass and weakens it. It will cause those corroded spots to become thin and the cases could rupture when firing.
There are non-ammonia based cleaners available but the steel wool mentioned would work fine as long as the corrosion isn’t too bad. If the corrosion is excessive, I’d get new ammo and discard the corroded stuff.


Sent from my iPhone using Tapatalk
 
The "tumble, don't tumble live ammo" controversy has been going on since I started visiting reloading forums in 2008, prolly longer, but that's when I started seeing it. I have seen no definitive proof from either side, just 99.9% speculation. I've read "tests" for "pro tumbling" and I've read posts citing a reloading manual. But I have tumbled some live ammo (200 old tarnished military surplus 30-06) with zero ill effects...

For a brand new reloader; don't get too involved with tumbling, it's 99% cosmetic. K.I.S.S. I started tumbling 12 years after I started reloading (I just wiped each case with a solvent dampened rag as I inspected it. no ruined dies, no scratched chambers). I started with a Harbor Freight rock tumbler and some walnut litter from Petsmart (dark). Works quite well. I now have a larger rotary and a wobbler, both work well with corn cob blast media...
 
Last edited:
Roaman Wade said:
Hmm, I wouldn’t have thought that the powder inside the shell could break down in such a way that it would cause a dangerous pressure issue.
Click to expand...

It's not. Keep in mind that manufacturers tumble canister grade powder to blend it with faster or slower lots of the same type powder to control lot burn rate variation. Also, keep in mind cartidges get vibrated in transportation, some of that being pretty vigorous with military transport, where it is subject to all manner of shaking, from trucks to air transport to parachute drops. It has to be able tolerate a good bit of this. actual testing shows no measurable effect. Read the whole thread at THR to get some sense of how the argument swings back and forth, but at this point I have to say I think most of the concern stems from manufacturer's concerns about liability rather than actual science. Still, in theory, tumbling can't go on forever before vibration finally does start to wear through the deterrent coating, speeding up the burn rate of the powder. But for a reasonable amount of time, it shouldn't be an issue.

My advice to you is to mix a 10% solution of citric acid in water and dab it onto the corroded places with a Q-tip to remove verdigris and white oxide blooming you see. Just keep any liquid the heck away from the primer pocket or it will wick in with unpredictable results for ignition. Ignore black oxide. It's stable the same as an annealing stain is. Some pinkish copper-colored red copper oxide will be left behind from the spot treatment. Ignore that, too. Rinse the dabbed spots off with plain water on another Q-tip. You can wipe it off with a rag dampened with distilled water to prevent water spots. The citric acid, unlike the vinegar and sulfamic acid sometimes used in case cleaning, will leave the surface passive, so it won't tend to re-oxidize.

If you are determined to shine it up before shooting them, I would go ahead, but I would test the result, just to be sure, given the lively debate on the subject. You could pull a few bullets and take the charge down 10% on one, 8% on the next 6% on the next and so on, until you are back to full charge. Reseat the reduced loads and fire them as a low-to high series while watching for pressure signs.

I don't know the age of your cartridges nor what tumbling might to do powder that was starting to break down. But that bullet-pulling will also give you a chance to confirm the powder isn't sticky or acrid-smelling and to dump some on a piece of white paper to make sure there is no red dust left behind when you pour it back into the case. If it has any of those signs of breaking down, I would be pulling all the bullets and dumping the powder on the lawn.
 
I use a little 0000 steel wool to remove corrosion from loaded rounds , do it while watching TV . Don't tumble .
Gary
 
I think everyone has to read Unclenicks comments and do what they think is for them.

I did get a couple of boxes of HXP and as it was slightly tarnished/ corroded, it got tumbled and cleaned up.

It shoots as poorly as it ever did! (but no sticky bolt either)
 
Took me awhile to relocate this thread. Unfortunately, it is a victim of the great Photobucket marketing blunder and all the nice high magnification photos of the powder grains are gone, though the titles are not. The bottom line was he accrued 300 hours of tumbling of some rounds and they still worked normally and he could see no difference in the powders before and after. Again, a deteriorating powder may be another matter, but I don't have data for that.

Anyway, the warning never to tumble loaded rounds (if the powder is in good condition) has looked more and more like a wive's tale to me as time goes by. Still, I don't blame the powder companies for nay-saying the practice as there is no upside for them to saying you can do it. If they say it's OK, sooner or later some numbskull will tumble a case with a double-charge in it and then blame tumbling the powder for causing the problem, and by extention, the maker who OK'd doing it.
 
On Thr they tumbled pistol loads for up to 40hr straight and checked for velocity changes afterwards and didn't see any.

I tumble all my pistol loads except hollow points because my rotary tumbler packs the hollow point full and they are a bugger to clean back out.

I don't tumble rifle loads with soft lead tips. I tried it and my rotary tumbler beat the snot out the tips, bent them and marred them all up.

A vibratory may not hurt the tips but I only recently bought my first vibratory tumbler from a Black Friday sale.

My rotary is still running strong after 35years (homemade) but I couldn't resist the deal on the vibratory.

I will have to try this to see if the vibratory will beat them up or they will to heavy to tumble and just lay on bottom.

I have some old beat up .308s that look like I found them in swamp.

I'll put them in tonight to see if they will even tumble.
 
Well, I through 3 of them in the vibratory tumbler and they sank like the titanic and didn't move after that.

If I left them in there overnight it may shine them up a little but after about an hour I couldn't tell any difference from when I through them in. They just weigh too much to move around in there and get the full benefit that an empty case gets.

I wouldn't waste my time unless you have nothing else to do. It certainly won't hurt them if they are healthy to start with.
These .308s of mine are going to be torn down and dumped out. I've been dumping a lot of rifle cases lately, stuff that's 30+ years old that has been carried a lot during hunting.
Follow what the other members here said and polish them out by hand. I use Never Dull for that, it will work after all the green stuff is off of them.
 
Never use brasso or other polishes that contain ammonia on ammo components. Ammonia breaks down the brass and weakens it. It will cause those corroded spots to become thin and the cases could rupture when firing.
Click to expand...
Nonsense. As understood it's a one time cleaning of exterior surface corrosion. #0000 steel-wool is likely to scratch away more brass material overall than a light coat of Brasso.
 
Quote:
Never use brasso or other polishes that contain ammonia on ammo components. Ammonia breaks down the brass and weakens it. It will cause those corroded spots to become thin and the cases could rupture when firing.

Nonsense. As understood it's a one time cleaning of exterior surface corrosion. #0000 steel-wool is likely to scratch away more brass material overall than a light coat of Brasso.
Click to expand...

The problem with ammonia is not that it will "scratch away more brass material", it is the metallurgical breaking down and weakening of brass. It is a known fact - ask any chemist.

Don
 
The problem with ammonia is not that it will "scratch away more brass material", it is the metallurgical breaking down and weakening of brass. It is a known fact - ask any chemist. USSR
Click to expand...

This ^^. I did a bit of research the first time I read "use no ammonia" and USSR's info is correct, a chemical reaction can take place between the ammonia and brass. Weakening of the brass (I read a "side story" that once in WWI (?) a camp of soldiers stored some ammo next to the horse stalls and some of the ammo was ruined by the horse pee's ammonia content. Internet "story"? or true?)..
 
It's called "season cracking" because it was discovered by the British army in India that their case neck would start to split during the rainy season (monsoon season). They had the habit of storing ammunition supplies in their horse stables, and in the near 100% RH of the rainy season the manure and straw would start to compost and release the ammonia gas familiar to any home gardener who has ever turned a hot compost pile.

The Wikipedia has a write-up on it.

I can't recall if it was on our board or another, but someone did post about polishing ammunition with brasso and putting it in machinegun links to hang on the wall of his bedroom in high school. When he went to college the belts were stored in a trunk and he didn't see them again for 20 years. When he finally did open the trunk up he said there was powder spilled all over from cases that had opened up and corroded.

The problem with that kind of annecdotal tale is that I have no way to know if the Brasso did it or if the powder broke down and corroded the cases open from the inside. I've had that happen with odd surplus cartridges. I also know people who've used Brasso on cases and not identified any clear problem resulting from it, probably because the exposure was short. On the other hand, given that season cracking is a known thing, and given that there are ammonia-free brass polishes from Flitz and all the sellers of tumblers and even home recipes (make a slurry of mineral spirits and diatomaceous earth from the garden store) I can see no reason to use it.
 
Thank you Unclenick! I think I land in your camp about all this. I collect bullets and I was thinking of doing this but a few days ago I got 3 full boxes of Federal 30-06 and 2 full boxes of 30 cal carbine that was lightly corroded but other than that looked fine. The boxes are new looking so I decided I'd try this and after hearing what you've said, I'm going to try it. Thanks again...
 
Roamin Wade asked:
Can I put whole loaded bullets into a tumbler to polish the corrosion off of them?
Click to expand...

Be careful to distinguish "tarnish" of brass cases from "corrosion". Tarnish is simply the oxidation of the surface layer of copper in the case which produces a brown patina like an old penny. Corrosion involves an "attack" on the structure of the case involving both the copper and the zinc. It will generally be colorful, but may also manifest as a black spot that goes well below the surface of the brass.

That said, my answer is: Yes, provided what you are describing as "corrosion" is limited to the surface of the brass. If tumbling - or after tumbling - polishing with Brasso or a similar cleaner will not remove the defect, the round should be salvaged or discarded.

Tumbling brass will not cause it to ignite. It will not cause the powder to break into smaller pieces causing excessive pressure. It will not cause the bullet to loosen. Ammunition manufacturers tumble their rounds before packaging them to ensure they are cosmetically acceptable to the consumer. If tumbling ammunition was a "No-No", do you think the manufacturers would do it?

Of course not. The imagined - but yet to be demonstrated - effects of tumbling on loaded round are among the reloading community's equivalent of "urban myths".

They are illusion and should be ignored.

And as we have already seen, there is no greater urban myth within the reloading community than the one claiming Brasso and other cleaners that contain ammonia will damage brass. The reality is that exposure to small amounts of ammonia for short periods of time poses no threat for cartridge brass made after the late 1920's.

In the 19th Century, the British Army in India found their cartridge cases were developing cracks after being stored in the horse stables for months at a time. This is called "season cracking" because it only appeared after the ammunition had been stored in the stables for months. It was later determined that storing ammunition in the stables where horse urine produced copious amounts of ammonia was causing cracking in UNANNEALED cases (note the cases affected were NOT annealed). The cracks were caused when some of the copper in the brass reacted with the ammonia along the unrelieved stress cracks that were created when the case was formed.

Since the late 1920's, when the phenomenon of "season cracking" was scientifically explained, ALL cartridge cases have been annealed during manufacture. Thus, the circumstances necessary for "season cracking" to occur NO LONGER EXIST. Whether it is even possible for a case made in the last century to EVER be susceptible to "season cracking" is doubtful. But, it is clear the tiny amount of ammonia in cleaners like Brasso and the short time the brass is exposed to the ammonia (minutes instead of months) is in no way comparable to the conditions that lead to "season cracking".

Brasso is NOT "bad for brass". The circumstances that made ammonia a threat simply NO LONGER EXIST. Nevertheless, the "old wives' tales" seem to have a life of their own.
 
You must log in or register to reply here.
Back
Top