I'm Ready To Start Reloading

I agree. I got a digital at first but if you take too long between uses, it would shut off. Beam scale stays on setting unless you hit, change or drop it. Beam is also a bit more critical of breezes, etc
Click to expand...
.

No its not, a digital scale is very sensitive to any air flow.

If its the kind that times out (battery) then you just turn it back on!

Now don't get me wrong, if it does not suit you that's more than fine, but to say give it up for that kind of reasoning is simply wrong.

Now, present what annoys you about them, that's what advice is about, then the OP can decide for himself.

And he has it and he might as well try it and see ?

Heavens forbid, he might like it! Then where are we?
 
Re: scales. The OP said his space was limited, and that he is reloading handgun cartridges. A digital scale stores easily and is plenty accurate enough for what OP is doing.
 
Getting the hand press is a great start. It will very, very, very quickly teach you a bench mounted press was the way to go from day one.

Even with a clamped bench mounted press you can easily fit all the tools into a medium size tool box and store it in the closet when not in use.
 
Wow! This is great! Along with all the suggestions in the thread, some of you have sent me PMs offering advice if I need it along the way. That is so awesome! It really means a lot to me. I've only made a few gun toting friends so far (4), but none of them reload, so they haven't been able to offer much advice. One of them does want to come over and help out though, when I get started, because he's thinking about getting into it too. Thank you! :)
 
No, you're not quite ready yet. Looks like you have been advised on tools for assembling the rounds. But like the rest of us, you will probably make some bad loads or mistakes along the way that may require disassembling the round (s) to recover the components. For that you will need a bullet puller. There are two common types, an inertia puller that is a general type, and a collet type requiring a separate collet die per bullet caliber. Get one of the inertia types, the only downside being that light bullets can be difficult to dislodge. The inertia puller looks like a plastic hammer.
 
Last edited:
I would get a powder dispenser and throw away the powder scoops.
I would get a table press and throw away the handheld press.
I would also get lube for the brass cases.
 
As condor bravo mentioned a bullet puller , an your ready to go , never used a hand press or loaded at the range but for now it will do the job. When your ready for a mounted press , you can't go wrong with a single stage RCBS Rock chucker , its the one an only press I've been using for 25+ years . Never had a problem with it , dies too . Now get going an do some reloads. Welcome to the club. Chris
 
I would get a powder dispenser and throw away the powder scoops.
I would get a table press and throw away the handheld press.
I would also get lube for the brass cases.
Click to expand...

One out of 3 is a good batting average.

lube is critical.
 
that's all great and you've gotten lots of good advice but I don't see any thing to clean your brass. A cheap and viable set up I use is the double tumbler from Harbor freight and SS pins. Check it out on you-tube there's tons of vids on how it's done.
 
I would get a powder dispenser and throw away the powder scoops.
I would get a table press and throw away the handheld press.
I would also get lube for the brass cases.
Click to expand...

^^^If your goal is to make ammo to shoot in any reasonable quantity, these items are key....

If you just want to putz around, then ignore my advice.

From what I gather from your initial post is tou are looking to dip your toes in with reloading and load 38 spcl.

You need:
Bench
Bench mounted quality press
Scale
Powder measure
Dies
Calipers

You want:
Case cleaner
Scale check weights

You may want to consider:
Case gage
Case trimmer
Case prep tools
Turret or Progressive press
Powder dispenser
Other toys!
 
Son did you get started on that room under the stairs yet?

Makes me think of the horror movie "The People Who Lived Under the Stairs". Just kidding. Sounds like it should be a great space once you get it done.
 
I built up a reload bench in a closet (no stairs of course) in a 10 foot camp trailer.

Worked fine for pistol.
 
Well, I wasn't able to put my order in this weekend. Gonna hafta to wait at least until next payday. It would be nice if I had been born with more money instead of so good looking! (Mac Davis anyone?) Hehehehe! :D
 
for cleaning just plain old soap and water in a bucket will do the trick until you get a tumbler of some sort. It won't make them shiny but as long as the dirt is off so they won't scratch the dies they are good to go. Shiny is purty but trust me clean and shiny don't shoot any better than clean and dull.

I used a wood lathe with a piece of 4 inch PVC and caps to dry tumble for years. When I sold my lathe all I did for about 3- 4 years was wash my cases with some hot water, detergent and a teaspoon of white vinegar then dried them on a towel. I never noticed any group size changes because my cases did not shine.
 
Personally I like digital scales. They are quicker, more accurate (make me feel better) and versatile to me.
Click to expand...
I have been loading since the sixties and have gone through three digital scales. All three eventually failed. Also during that time, I have had three balance beam scales...one burned in a house fire, I sold one when moving and there other is still in use. Digital scales may have some apparent advantages, but mechanical balance beam scales do not fail.
 
I do want to be clear, I don't feel beams are bad.

But yes they can fail. Different sort of failure. They can be damaged to where they won't work and you have a failure on your hands.

For me, they are slower (too slow) , they are hard to settle down and they are not versatile.

Yes you are right. Digitals in all likely hood will fail.

Question is does the convenience and vastly more versatile of a digital overcome the failure?

Its a matter of what works best for a person, not what is right or wrong.

I won't go back to a beam, I won't recommend it to a new re loader because I think the digital is a major improvement.

If they feel a beam is the better solution after weight the pro and con, good to go.
 
those who reload for any length of time usually acquire both a digital and a beam scale. My beam keeps the digital honest
 
Well, I am disappointed. I got up this morning, ready to place my order with Midway, and they are out of stock on the hand loader and dies. I didn't bother looking anything else on my list looked up. I signed up to be notified when they're back in stock. I tried Amazon, but their prices are higher, so I guess I'm going to have to wait. :(
 
But yes they can fail. Different sort of failure. They can be damaged to where they won't work and you have a failure on your hands.
Click to expand...
My digital scales failed spontaneously. Balance Beam scales, on the other hand, must be wrecked via accident, negligence, misadventure, etc., whereas digital scales can just up and quit for no physically apparent reason. I got tired of buying new digital and have not replaced my current balance beam for at least 25 years.
 
You must log in or register to reply here.
Back
Top