I just screwed up my colt 1911

The Dremel is a tool, just like any other tool. Don't blame the tool for what happens when folks don't know how to use it (and when NOT to use it).

Jim
 
I did not need help understanding how stupid I was. I got that all by my self. Clark customs said $700+ new ramped barrel bushing and an action job,8-10 month.Or Triangle shooting sports came highly recommended $400 ramped kart bushing link tuning and fitting 4-6 week turnaround. Mr.Hill said he would take one of my other guns guns for payment.
 
It might have been a long day hot sun and cold bxxr. maybe I end up with a better gun. I know I will have more money in it.
 
Yes and unfortunately an expensive lesson learned. As they say when in doubt leave it alone or to the pro's.
 
I talked to Mr. Hill again. He told me. He said he can rework the breach of the barrel. 75.00 to 100.00 $. I don't know witch way to go.
 
Go back and re-read what Mr. Hunter said in post #10.
http://forums.1911forum.com/showthread.php?t=146569&highlight=ramp+insert
I had this process done to an alloy-framed 1911 that a previous owner had sanded or Dremel'ed to death. This is a precision machining job that restores the frame ramp to its original dimesnsions with a piece of stainless steel permanently fitted to the frame.

If the barrel has been mega-buggered, you may have to replace it as well.
 
Dremel

The "Dremel Philosophy", "My 1911 has always feed and functioned perfectly. But, I have just noticed that the feed-ramp is a little rough...hey! I can "fix" that, I have a Dremel!"
"If you just cannot leave well enough alone, the Dremel is the perfect tool for you." Dremel Company Slogan.
 
Check out Jerry Kuhnhausen's book on the 1911. Never says anything about touching the frame ramp.
Click to expand...
But, hey...I have a Dremel and I can see the roughness. I think that I will "smooth up" the barrel too while I am at it. Even though there is no feeding problem. What can go wrong...I have Jerry Kuhnhausen's book.
 
Yeah, you're right, dahermit–he mentions the frame ramp very briefly, one scant paragraph...basically says polish it, nothing else. I heard the same thing from another well-known smith. This thread interested me because I may throat a barrel to feed wadcutters, and I don't want to bugger it. You're also right in that no book is a substitute for common sense.
 
Last edited:
Before you do any ramping or other alteration, know this...

1. The 1911 platform--specifically, the .45 ACP--has been provided for some time with barrels that have already been throated for reliable feeding.

2. There are two "bumps" on the frame, each side of the feed ramp. These are called bullet guides, and they are there by design. Do NOT reduce or alter these in ANY way.

3. To check your 1911 for feeding reliably, do the following steps first: a. Obtain good magazines that have the feed lips configured for wadcutter ammunition. b. More than likely, you will be reloading unless you have a ton of money to spend on match wadcutter ammunition. If you are reloading, the secret is to load the round to the same OAL as a round of ball ammunition. The pistol is manufactured and timed to work with that bullet length. c. Make sure your round is taper crimped properly. I use a taper crimp of .470, measured at the case mouth.

In closing, check that your ammunition is within the same specs as a round of ball ammunition before modifying your pistol.
 
Hey I once got a strut out of a toyota pickup only to discover that the tools to install the new ones were not at my disposal.

Drove said truck to the dealer with a 2x4 installed where a strut should be.

My hat is off to anyone who tries, way more than folks who act like fixing guns or anything is some magic process mere mortals can not consider.

Expensive lesson though....
 
Heh, I wrench in a dealership.
We would have had a great time with that!:D
It would be like Cheers...where every body knows your name...
Joe
 
I remember the first time I built my own 1911. Over the years--part of that time working as a gunsmith--I learned the following things:

1. Drop in parts don't.
2. Measure three or four times. Then measure again.
3. Stones cut faster than you think.
4. The same stones do not survive being dropped too well.
5. There is a Box O' Truth. It tests bullet performance. There is also a Box O' Gun. It tests your wallet and/or credit card's performance.
6. Dremel and Foredom tools are magic. You can go from "Here I go...." to "Oh crap, I've ruined the gun" in 10 seconds or less.
7. Books have been published and videos made on the subject for a reason.

And the important lesson is:

8. ALWAYS cut on or adjust the cheapest part FIRST.
 
You must log in or register to reply here.
Back
Top