Another Pietta horror story

pietta

What model is it? I'm curious.
Not everything to leave the factory is junk. I have had an 1858 .36 New Army Police for some years now and it has worked perfectly. Sorry to hear that they aren't all like that.
Pete
 
Pietta horror

I bought my first C&B revolver from Cabelas about 4 years ago, and being VERY green to to these types of revolvers, I bought one that was on sale, new in box.....a brass frame 1851 in .44, with a round barrel, Pieatta of course, and instead of buying the starter kit, I just bought some Remington #10 caps, a box of 100 .451 round balls, some Cabelas lubed wonder wads, a tube of bore butter, and a can of FFg pyrodex.

Now, I had done a small bit of research, you know, how to load, how to shoot, how to clean, etc., so I took it camping and loaded it, by the book, aimed at target...and Boom!!...Went to cock hammer for second shot, and it was completely froze up. I couldnt budge hammer or cylinder in any way. Needless to say...I was bummed. So, being as how I couldnt turn the cylinder.....I took it back to Cabelas.....caps on nipples and all.....I know..very stupid..but what could I do? Anyways, they were very professional about it, (not to mention very cautous about it), and told me to pick another one out, or take receipt to customer service for a refund...and I respected that.

I'm not bashing Cabela's in any way, for they were courtious enough about the situation, but it did hamper my enthuisiam for B&C revolvers. Anyway, I did trade it in for another (gasp) brass frame "51 Navy .44...and after repeating the same procedure as before...this one worked perfectlly. As far as mass emailing Pietta, Ive sent them 4 emails about their revolvers...and not one response was ever recieved. Anyways..I'll get off my soapbox about Pieatta now...I reckon its like buyin a car..Some are downright badass's..and some are just junk....but still...I'm not returning this revolver, I plan on trying my best to smooth out the rough edges and make her into a decent investment!
 
Two of my revolvers I bought as nib Pietta's, both came out of the box very nice revolvers. The 1858 did need some stoning to get rid of the trigger creep, the 51 brass .44 has been a great shooter, tight barrel gap and very smooth action. A nib Uberti Baby Dragoon was unshootable out of the box. It did give me several hours of enjoyment repairing it. One nib High Standard 51 needed a LOT of work to be right. A couple of 2nd and 3rd gen Colts that needed minor attention. All the manufacturers have bad ones slip by QC.
 
...err....haven't I been reading, on these very pages, how Pietta and Uberti are pretty even in terms of quality? I'm just curious about this "another" horror story about Pietta

I had thought we generally agreed that Piettas being junk was a misconception
 
I had thought we generally agreed that Piettas being junk was a misconception
Click to expand...
I have several Piettas and several Ubertis and don't consider any of them junk, I think for the money thier a real bargain, but I think the quality does vary from revolver to revolver and some less then perfect specimens do hit the market. I tend to like the Ubertis a bit more but that is just a personal preference.
 
OP- go out and buy a Ruger Old Army. When you pick it up, look at it, and cock it ONE TIME, you'll want to sell all those Italian pistols- and buy a 2nd Ruger.

The quality gap is vast, Ruger to Italian replica. The Italian replicas are neat, they have their place, but they are a cheap gun compared to a Ruger.
 
Quote:
I had thought we generally agreed that Piettas being junk was a misconception
I have several Piettas and several Ubertis and don't consider any of them junk, I think for the money thier a real bargain, but I think the quality does vary from revolver to revolver and some less then perfect specimens do hit the market. I tend to like the Ubertis a bit more but that is just a personal preference.
Click to expand...

+1
Every manufacture has some bad revolvers on the market. It seems to be the luck of the draw on what you well get. The general consensus is Uberti is a little better than Pietta, that has not been my personal experience.
 
The general consensus is Uberti is a little better than Pietta, that has not been my personal experience.
Click to expand...
Yeah, I didn't mean to imply that Uberti is better than Pietta. I like the Uberti a little better because of the way they stamp the barrels.
 
the Piettas seem to have a dry, harsh, rough action in the hammer/lock, not as smooth as Ubertis.

the imports are not a bad gun if viewed as a "gun kit" that you take apart, fix, and customize/build

problem is, they don't sell at kit prices. The guns should be around $100 if you have to rework them like that

not $250-$300
 
Hmm. I've said it before, and I will say it again-

I am the luckiest SOB that ever bought a gun. My P22 is 1200 rounds with zero failures to feed, two failures to extract, and two bent rounds, my Auto-Ordnance 1911A1 is nearly flawless in over 1,000 rounds, I can hit what I aim at with my 89 year old Colt M1903, and my c&b Pietta Colt repro (from the late '80s!) is great, never been apart and works like a dream. Everyone else seems to have trouble with those guns though

It's a product of my clean living and a humble god-fearing attitude, I tells ya! :D
 
I had thought we generally agreed that Piettas being junk was a misconception
Click to expand...
One incident should not influence that conclusion one way or the other. Making the judgment that the characterization of Piettas as not being junk was wrong on the basis of one report is making a very unwarranted generalization. You need to back off a bit and consider the broader picture.
 
I don't want to step on anybodys toes nor attempt to fracture the brand loyalty,but Ive personally had extremely bad luck with the Pietta 1860 Colts.Put alot of effort and extra money in the process of trying to own one too.
Yall might remember my first one that I cried,kicked and screamed about.It was a 2007 production per the date code and under the Traditions label.It had a loose arbor in the frame right out of the box,poorly timed to say the least,the barrel fit so tightly on the arbor it had to be driven apart.Made the huge mistake and sent it back to Traditions and they attempted to repair it rather than replace it.Make note that I said attempted.
Since that one I have made an attempt three different times in buying a Pietta 1860 Colt...all were 2008 manufacture.All had serious fit and function issues.
Now being that the revolers were from two different retailers and two different years of manufacture,I came to the conclusion it was not just bad luck on my part.To be honest the overall experience almost turned me away from wanting another cap-n-ball revolver.
I finally gave up on mail ordering a Pietta Colt after about two months of back and forth,and went to the local gunshop to eye ball in person.Ended up going home with a Uberti 1860 Army.
Now,I have a Uberti Walker,Whitneyville Dragoon and a 1860 Colt Army.All of which were perfect right out of the box and only needed some bolt and trigger spring adjustment.I may have gotten lucky with the Uberti's...but I'll take it.
Do I think Uberti is perfect?No,absolutely not.Ive seen a couple with minor issues as well.But I do think Uberti has much better quality control and materials overall.IMHO the steel Pietta uses in the Colt replica barrels and cylinders is fairly soft especially when compared to what is used by Uberti.
I can say without a doubt that my Pietta 1858 Rems were outstanding in everyway right out of the box,and continue to be.Can't say enough about Pietta in regards to the Remington replicas.I don't know how they can build the 1858 Remingtons so well and make such a mess out of some of the Colts,but that seems to be the case in my experience.
Again,I do not intend to offend anyone of flame anyone else with my opinion and personal experience.I own both Pietta and Uberti replicas and Im very fond of them all.But I do think Pietta can and should do much better with their Colt replicas...they owe it to their customers to pay a bit more attention to what they are turning out for sale and improve in that regard..
But thats my opinion.
 
Last edited:
I'm with you Chris

I must be lucky SOB #2

I have had a great run with guns :D Mostly the ones the 'horror stories' are about.

I have a P22..... no issues
2x Pietta 1858's...... no issues
1x Euroarms of America 1858..... previous owner bastardised it, so issues, but not with manufacturer.
1x Uberti Colt Dragoon..... no issues
2x Stainless steel ROA's...... Absolutely no issues :D

I think Pietta & Uberti are on par, from what I have heard.... if you get a good one, it will be great (up to standard) If you get a lemon.... well, you got a lemon, if you buy it from a reputable dealer, take it back, that's what guarantee's are for. If I were buying another Pietta or Uberti, after hearing these horror stories, I would just be inspecting it thuroughly at the place of purchase before parting with the cash, rather than get one sent in the post or whatever, just to be sure there is nothing obviously wrong with it, then test it & if issues are found with its shooting, take it back again :D
 
Well, my first C&B revolver was a Pietta .44 brass frame that was given to me about 35 years ago. I still have it, but it's looser than...well, let's just say that too many full-loads went through it before I knew any better. :( I still have it and it's shootable- never had any problems out of it at all that weren't user inflicted.

I now have a good collection of C&B revolvers, the majority of which are Pietta manufacture and have never had any problems out of them other than losing parts I drop on the floor. :o

I hope to get some pictures this weekend of them all being out on the range.

I can certainly understand the frustration of buying a product and it not behaving the way it was intended.
 
HEY DINGO how you doing sport,:D
to say you live down under you got a butt load
of guns:confused: i thought you guys were
under a gun control.
 
Hey LR

Yup, down under

Yup, butt load of guns..... Our rules are strict, you have to have a purpose for guns (especially HG's) and SD or HD are not legitimate purposes. I shoot in 4 clubs (2 x Black powder clubs, CAS & with the local police (protective services pistol club).... so I have lots of purposes (for lots of HG's) :D

Read the thread below I posted a while back, it will fill you in, it is a long read but will answer most of your questions :D

http://thefiringline.com/forums/showthread.php?t=344538&highlight=handguns+down+under
 
I don't get it.

For years I've been reading on various boards that "Pietta is now right up there with Uberti," "Pietta has gotten their act together," "Piettas are the best bang for the buck," etc.

Every one that I've handled/purchased has had obvious problems, sometimes multiple obvious problems.

Maybe I've had a long stroke of bad luck. But as time goes on, and I see more and more bad ones, I think this less and less.
 
WELL some folks said that asm was trash? but i
have one a 58 its now 15 years old and still going
strong, so what the heck. i think we all agree that
there are lemons out there, and some guys get the
lemon now and again :rolleyes:
 
I don't get it.

For years I've been reading on various boards that "Pietta is now right up there with Uberti," "Pietta has gotten their act together," "Piettas are the best bang for the buck," etc.

Every one that I've handled/purchased has had obvious problems, sometimes multiple obvious problems.

Maybe I've had a long stroke of bad luck. But as time goes on, and I see more and more bad ones, I think this less and less.
Click to expand...

I've had two new ones and one used one and no problems with any of them.
 
You must log in or register to reply here.
Back
Top