What is your definition of reliable ammo

M

Metal god

New member
Rimfire need not apply !!!!!

OK now in the last 6 months or so i've shot a few thousand rounds ( give or take ) of 223 , 5.56 , .308 , 30-06 , 12 gauge , 9mm , 380 , 40 S&W . All factory ammo off the shelf

There are a few things I am starting to notice .

1) . I never have any prolems with hand gun ammo , It always goes bang when I pull the trigger and I think thats all Im looking for out of hand gun ammo . DOES IT GO BANG EVERY TIME ? I do have nice hand guns IMO , XD , beretta , ruger . That may make a difference .

2 ) . As for rifle ammo . Does it simply have to go bang every time for it to be reliable or is there more you expect out of your rifle ammo ? hand gun ammo for that matter as well .

3 ) . Yes we all want the ammo to be as accurate as any given gun can shot it , but does that have anything to do with reliability ?

4 ) . Im seing less problems in general with bolt action vs semi auto's . I assume this is do to the fact there is just a hole lot less going on in a bolt action then a semi auto while being fired , YES ?
 
Last edited:
My definition of reliable ammo for a handgun is that it goes bang and exits the muzzle with the proper velocity and can cycle the gun. For basic defensive rifle shooting it's about the same as for a handgun, go bang and have the proper velocity since I most likely won't be going out passed 50 yards. If you are say a designated marksman or sniper than I expect everything I said with defensive shooting plus precise accuracy and consistency; In that role 1 shot may be the difference between life and death for your brothers in arms.
 
Going "bang" means nothing if it doesn't consistently hit the target.
Click to expand...

Conversely, hitting the target on every round fired, but only on the odd occasions the ammo goes "bang" is also less than ideal
 
I don't recall any rifle ammo ever failing to fire in any of my rifles. Factory or handloads.

I've never had any problem getting sub-MOA out of some tailored handload. I've found some factory ammo which is sub-MOA in a rifle of mine, but it sometimes takes trying different brands.
 
I have been averaging 1 out of a hundred or so failer to fire with lake city m193 . Some say light primer strike . They look like good primer strikes to me . I would think if the gun was prone to light strikes . i would have more failers to fire then 1 out of 100 .

I also have had two .308 failers in a bolt action recently . One was Tulla and the other was Winchester X "something I forget ( gray box ). both apeared to have good primer stikes .

The other day at the range I had one box of steel cased 223 that I had 3 feed jams and two failers to fire out of 20 rounds . Unfortinately I took them out of the box some time prior to going to the range and I do not remember the brand . I want to say WPA but Im not completly sure . The box was more square then rectangle. Those were the first 20 of the day . I also had 160 rounds of brown bear with me and I did not have one failer to feed or fire with those . Both ammo's fired out of the same gun . I have one AR that I only shoot steel case ammo out of . The rest only brass . Kinda running my own little test .

I have been shooting alot of different ammo out of all of my fire arms . Been trying to find what works best for each .That way I know what to put away for a rainy day

Like I said before , my hand guns don't seem to care . They eat what ever I give them .

Im still working on my AR's . They all love the good stuff ( $20 a box ) But when it comes to the cheeper stuff . They like PMC , Remington UMC , and they really like the Federal AR223 ( black box ) . Now when I say " like " , I mean it goes bang every time and is reasonably accurate ( 2 to 3 MOA at 100 yards ). By saying ( goes bang every time )that to me means it is cycling every time as well or it would just go bang once .

What do you consider is reasonably accurate for a 223/5.56 plinking round under $10 a box ( in MOA ) .With the good stuff ( $20 a box ) the best I can do is 1 MOA with Federal gold metal match al 100 yards using a scope . The majority of my plinking is done with iron sights or a red-dot .

I do not reload at this time but I do keep all my brass for when I do start reloading .
 
I don't recall any rifle ammo ever failing to fire in any of my rifles. Factory or handloads.
Click to expand...

I had some third-hand handloads hang-fire a couple years back. However... they had been stored in very poor conditions, and were handloaded in 1963 and 1969.
(The chain of custody could be traced and trusted for the handloads; and I verified the load data before attempting to fire them. I do value my eyes and fingers. ;))


I've haven't every had a factory ammo fail-to-fire or hang-fire in a rifle, that I can recall right now. But, I have had some ammunition that had incredible head space issues. Both bad boxes were from Federal.
The first problem was 0.130" excess head space with 150 gr 8x57JS ammo. Yes, that's one hundred thirty thousandths! :eek: I don't even understand how that could have happened with typical draw dies...
The second instance, was a box of Federal Power-Shok .243 Win where half the box would not chamber because the shoulder was 0.080" too far forward. Again... eighty thousandths! :rolleyes:

Federal, apparently, does not understand the concepts of head space and standard dimensions.

Those, to me, were very serious strikes against "reliability" -- One box of ammo that was downright dangerous to fire; and another where the ammunition couldn't even be chambered.
 
If you're getting that many failures to fire, I'd say its a gun problem, rather than an ammo problem. I've shot many thousands of rounds through AR's in the past and I can't recall any failures to fire in factory rounds. There may have been one or two, but it was so rare that I can't even remember it. Most was Lake City M-193, and PMC commercial M-193 back in the 80's. My guns were box stock Colts.

I know a guy that built an AR. He had some sort of match trigger, and had many failures. He thought it was the ammo (even shipped some back), but he had a lot of "ammo problems" before he put a regular trigger system in it, then the problems went away.

I had a problem with a Remigton 788 in 308 with military ammo. It didnt reliably ignite some of the cheap surpuls that was available at the time, so I sold it. The Ruger 77 I have has fired all the surplus stuff I've shot in it without incident.

So whats up with the 22 rimfire stuff? I've seen some allusions to it not being reliable. I've had very few problems with any that I've shot. More than centerfire, but nothing I'd consider worthy of comment.
 
Yea you caught me . The one AR that has the problems with the lake city stuff I did a fluff and buff on the trigger . Got it down to 4 lbs .I think me stoning and buffing the trigger and hammer so they are as smooth as glass is what droped the trigger wieght from 7 to 7 1/2 lbs to 4 lbs the most but I did bend the hammer sping a little , about 15 degrees . I'll put one of my extra hammer springs back in and see if I get less failers . ;)

As far as rimfire , I just felt the thread could get way out of control if people started talking about rimfire's and reliablity . I can give one example worth mentioning . I have put something like 800 to 1,000 rounds through my XD9 With no failers to feed , extract or fire ( NOT ONE ) it goes bang every time , Now with my Ruger mk3 I have shot 3 times that much out of it and well I have had many failers of all types . I would not say alot but many more then none like the XD . I now almost exclusively use some type of CCI out of all my .22lr and have almost no problems any more . IMO there is most certainly much more unreliable rimfire ammo out there then centerfire ammo . Thats why I did not want to get into rimfire reliablity issue :).
 
Last edited:
Aguila is on my 'very questionable' list. 2 years ago I was shooting the M1 Carbine match at Perry. Using issued ammo - Aguila. About halfway thorough a round many a funny sounding pop and peppered my face with blowback. What the? Didn't extract either. Stopped and pulled the case out. Hmmm, bullet still in place, primer struck and obviously went off and mostly missing. Pried out the remnants and looked underneath.. No flash hole!:eek:

Wow, that's weird, oh well, try again. Had another 15 or so rounds later. Yeah, okay, I'm done.
 
The only "unreliable" ammo I had experience with was 9mm surplus stuff that was meant for a submachine gun. It took 3-4 hammer strikes to make them go off. I ended up using them to cure my flinch.
 
In over 50 years of handloading, I've only had one handloaded round FTF in a bolt-action centerfire rifle. It happened last year with some primers bought recently at a gun show. They were either not made right or stored improperly prior to my getting them.



In my rifles, a good rifle round for hunting or defense, will feed from the magazine, enter the chamber easily, fire properly and be accurate to 1 MOA, or better (usually better), then extract easily and eject.

For bolt-action target and plinking, I don't mind if rounds fit a bit tighter and bolts close with a little more force, but not extreme force.

Regarding reloaded ammo reliability, I check rounds after sizing and after loading to assure they will feed properly in my rifles. Primers are checked by feel or sight as I seat them. I do one step at a time on all cases and don't turn a case neck-up until it's filled with powder. When filling with most powders, each charge is measured an weighed. Ball powder loads may be check-weighed after every five or ten, depending whether it's near maximum or not.

After filling all the cases, I inspect them in the block in good light, so I can see that they appear to have the proper amount of powder. That's critical IMHO!
 
I have shot a lot of old and questionable ammo and had misfires/hangfires. But I expected that, and was not concerned.

But with good ammo, I expect NO misfires. Theoretically, I might live with one in a million but the one in a hundred mentioned above is totally unacceptable. Something would have to be wrong with the gun or I would never buy that ammo again.

I also would not accept misfires from a new gun. Again, with antique guns, I can accept problems, even accept ones I can't fix. But with a gun I might need for defense, I believe in zero tolerance of misfires.

Jim
 
I have heard of having a squib that leaves the bullet lodged in the barrel, and the following shot causing a rupture.
 
I have shot a lot of old and questionable ammo and had misfires/hangfires. But I expected that, and was not concerned.
Click to expand...

Keep on shooting old and questionable ammo and you will eventually blow a firearm. You may not understand the chemistry but you will remember the effect.
 
You must log in or register to reply here.
Back
Top