Un-scope'ing a Rem 1100 skeet b

J

joeranger

New member
I got this in an estate sale "as is". At first I thought it was going to be a dedicated deer/slug gun. However, it looks like the scope mount (#885SGM) uses the existing holes for the attachment. I have not taken it apart yet but I am hoping I can get some replacement pins and us the gun for both deer and skeet.
Is anyone familiar with this kind of mount?
Is there anything wrong with the idea of the scope being removable? It should maintain enough accuracy for a slug gun.
 

Attachments

  • scoped 1100 1.jpg
    scoped 1100 1.jpg
    88.6 KB · Views: 53
Shoull not be a problem !!

Is anyone familiar with this kind of mount?
Click to expand...
Yes, for quite a number of years, I had one of these, on my 1100, until I finally bought a sighted slug barrel. You are correct in needing the original set of pins and still readily available, like from Brownell. My scope held up rather true from removal to install. However, I'm sure your will recheck prior to hunting with the slug barrel. Most of my Midwest shots were under 60yds. Take a closer look as this mount is probably a Tasco. ..... ;)

Be Safe !!!
 
Makes sense. It is a tasco scope.
Is there any value to this mount with a Tasco 2.5 x 32?
My other thought is to just scrap it. It seems too cumbersome for the value. As you say, most deer shots are 25-75yrds.
 
My SWAG on this is $30.00 to $35.00 for all.

My other thought is to just scrap it. It seems too cumbersome for the value.
Click to expand...
Well, this is certainly your call but by my measure there is value, although certianly not much. This is a typical combination of that era and fairly sure your scope is a Shothgun/ML rated scope with the longer eye relief. I know that there is still some interest out there for this set-up but again, very limited. Most guys have gone to aftermarket rifled cantalevered barrels.
I thought you were goind to keep this set-up? ... :confused:

One thing that you may find and not like very much, is the rub-marks on the side of your reciever. This is quite common when you have this metal to metal contact. .... ;)

Be Safe !!!
 
I am going to keep it as is. It is a "non-decision". My gunsmith thinks the holes were drilled out a bit to fit the screws.
I have a dedicated "deerslayer" :)
 
One step at a time !!!

My gunsmith thinks the holes were drilled out a bit to fit the screws.
Click to expand...

He may be right but I doubt it as these were made so you didn't have to drill out your reciever. If by chance some fool drilled them out, then you have a problem. First find out what you really have and then where to go next. ... ;)

Be Safe !!!
 
If you call Remington's Service Dept & just/simply tell them the trigger group retaining pins got lost, they'll most likely send you a set.

.
 
I've handled a couple of Remington shotguns with the sidemount attached by screws through the pin holes. If the screws were kept tight, the pins should fit properly. If it got loose and the screws jiggled around quite a bit, that might be a whole different deal. I saw one that had this happen and the solution was to drive a couple of roll pins through the egged out holes. Keep in mind those pins are not a tight fit and are held in place by a small keeper spring.
If you remove the scope, what is your alternative sighting equipment?
 
Well. Problem solved. A buddy we hunt with is getting married.
BEST WEDDING GIFT EVER!!!

I made the case myself. I love woodworking.
 

Attachments

  • Gun Case.jpg
    Gun Case.jpg
    206.1 KB · Views: 19
You must log in or register to reply here.
Back
Top