Tip For Non-Marring Colt Wedge Removal !!!!!

S

sltm1

New member
I was looking at another thread discussing the 800 lb gorrilla that install's the Colt wedge's at the Pietta factory. The trick to initial removal, and removal and replacement there after is this......wrap your hammer head in rawhide !!!! For you "city slicker's" and creatively challenged folks like me finding the rawhide is not as hard as you think. Go to your grocery store and buy an unflavored rawhide dog chew toy !! You can cut it down with a hand saw to the right length while it's hard, then soak it totally immersed overnight in a pan of water and the next day it's plyable. Wrap the head of your hammer and tie it on securely. Wait at least a day for it to dry out completely....then feel free to smack away with no damage to the gun barrel or wedge. I make small pocket hammers for shooters with a wedge puller and screwdriver added to it that works perfectly for shooting both Colt's and long rifles.
 

Attachments

  • WedgeHammers.jpg
    WedgeHammers.jpg
    49.6 KB · Views: 108
I've heard of wedges like that, never saw one tho. I just ordered a 51 Navy, maybe the wedge in it will give me some fun. If it does I guess I'll just use one of the plastic or rawhide hammers I've got laying around.
 
Guy's, guy's, guy's, this post is for those of us who haven't found perfect guns, or the ones who's barrel's stay firm without wobble with just thumb pressure....some of us are more prone to worshiping the "Immutable Law's of Murphy". And yeah, bronze is a good alternative also. I personally have both a Colt 62' Pocket Police (1/2 original and 1/2 Italian), and a Belgin Colt Model 1860 Centaure, both like the wedge to be jam tight, neither use the wedge to it's full length, but thumb pressure loosen's up the barrel to receiver fit and changes the cylinder gap and the accuracy. My hammer is also used regularly to remove the barrel off my T/C Renegade after the monthly shoot for cleaning, plus the screwdriver tip I whittled down to fit the hammer screw on the rifle, which likes to come loose after a dozen or so rounds. We all got trick's, I just like to share mine. Got any to post yourselves? Alway's willin' to learn somethin".
 
Put some blue Loctite on that hammer screw. Don't use red tho unless you want to use heat to get it back out.
 
I too use a rawhide mallet..mine is about 1 1/4" dia..solid rolled rawhide & wooden handle. Be careful with brass! though softer than steel..it will leave dents! With use, those wedges should loosen up a bit.
Just a thought..we gun owners of today really baby our guns..just look at some original percussion Colts..the area around that wedge looks like an anvil on some! Some are so bad it looks like they used a rock!..Maybe they did?
 
My guns were put together by the 800 pound gorilla too...I need one of these hammers. At least until the wedges start to loosen up. Good idea!
 
I use a junk screwdriver ground down to a wide flat, dipped in plastic goo for such things. Tap gently with a small peen hammer, works fine. Have yet to mar any finish.
 
Homemade Knocker

Brass plumbing with a hallow-ground screwdriver bit. Never leave home without it!


016.jpg



027.jpg
 
On my bench grinder I ground a piece of 1/4 inch aluminum to fit in the wedge hole. I only have to use it on one of my muzzleloading revolvers. The aluminum is softer than the steel and won't mar it. It also fits perfectly in size against the wedge's right side (just barely under the size of the wedge) and a light tap with anything against the aluminum knocks the wedge right out.



.
 
You must log in or register to reply here.
Back
Top