Mackie244Bud
New member
FYI..Sig is shipping the Manual Safety Parts to retrofit any P365.
Sig Sauer P365 Manual Safety, Non-Textured $26.78
Code: 2700056-00-R
https://www.midwestgunworks.com/page/mgwi/prod/2700056-00-r
Sig Sauer P365 Manual Safety Detent $8.30
Code: 2700290-R
https://www.midwestgunworks.com/page/mgwi/prod/2700290-r
Sig Sauer P365 Manual Safety Detent Spring $5.00
Code: 2700267-R
https://www.midwestgunworks.com/page/mgwi/prod/2700267-r
Total Cost with Shipping = $47.07
Here is a Vendor "AbPrototype" that sells all 3 MS parts in a Kit $39.99 + $4.00 Shipping - $44.00
https://www.abprototype.com/sig-p365-manual-safety-lever-assembly/
At the time of this post MGW & AbPrototype are "Out of Stock"
I ordered the above parts when they were "In Stock" and Retrofitted my P365 with a XL Grip Module.
I used a Dremel to cut the Grip Module on the Left Side (Controls Side) only.
I followed the rear Mold Mark on the Grip and cut to the lower mold mark line.
I then fitted the FCU with the Manual Safety installed into the Grip and I could see how far forward I needed to cut to clear the MS Lever Arm.
I cut the forward line down to the Mold Mark and then going back and forth removed the small piece of plastic in the middle.
I used the Dremel with a metal cutting Disc and cut the Right Side Lever off of the Manual Safety Lever.
I only wanted the Left Side Manual Safety Lever as I am Right Handed.
Fitting the Manual Safety Lever into the FCU was easier with the Trigger pulled back and the Trigger Return Spring Forward..leaves more space to slip in the Manual Safety Lever.
It came out very nice and Functions Perfectly.
The Blue Line shows where I cut the Manual Safety Lever..
https://vimeo.com/369664928
Sig Sauer P365 Manual Safety, Non-Textured $26.78
Code: 2700056-00-R
https://www.midwestgunworks.com/page/mgwi/prod/2700056-00-r
Sig Sauer P365 Manual Safety Detent $8.30
Code: 2700290-R
https://www.midwestgunworks.com/page/mgwi/prod/2700290-r
Sig Sauer P365 Manual Safety Detent Spring $5.00
Code: 2700267-R
https://www.midwestgunworks.com/page/mgwi/prod/2700267-r
Total Cost with Shipping = $47.07
Here is a Vendor "AbPrototype" that sells all 3 MS parts in a Kit $39.99 + $4.00 Shipping - $44.00
https://www.abprototype.com/sig-p365-manual-safety-lever-assembly/
At the time of this post MGW & AbPrototype are "Out of Stock"
I ordered the above parts when they were "In Stock" and Retrofitted my P365 with a XL Grip Module.
I used a Dremel to cut the Grip Module on the Left Side (Controls Side) only.
I followed the rear Mold Mark on the Grip and cut to the lower mold mark line.
I then fitted the FCU with the Manual Safety installed into the Grip and I could see how far forward I needed to cut to clear the MS Lever Arm.
I cut the forward line down to the Mold Mark and then going back and forth removed the small piece of plastic in the middle.
I used the Dremel with a metal cutting Disc and cut the Right Side Lever off of the Manual Safety Lever.
I only wanted the Left Side Manual Safety Lever as I am Right Handed.
Fitting the Manual Safety Lever into the FCU was easier with the Trigger pulled back and the Trigger Return Spring Forward..leaves more space to slip in the Manual Safety Lever.
It came out very nice and Functions Perfectly.
The Blue Line shows where I cut the Manual Safety Lever..
https://vimeo.com/369664928
Last edited: