Ruger American Barrel Removal

R

RCP Fab

New member
The thought of a heavy barrel has been plaguing my mind since I bought my RAR. Last night I decided I would pull the factory barrel and

a) make sure the barrel was easily removable
b) learn some more about the factory barrel

The RAR is set up with a smooth barrel nut like some of the savages, but none of the dimensions are the same.

Clamp the receiver in a vise, I used my bridgeport vise. There are 2 flats on ether side of the receiver. It does not have to be clamped all that tight, if you have a good vise.

The barrel nut is torqued ridiculously tight. So tight that the small area under the barrel that was missing some bluing made me question if the nut was soldered on, but it is not.

Using a strap wrench was a waste of time. Some people say to use a pipe wrench on the savages, then replace the nut. I opted to make a tool.

A few taps and the nut comes loose, remove the tool and back the barrel out by hand.

To reinstall, use a go gauge, or a piece of brass that was fired from your rifle (not resized). Start the barrel in the receiver and chamber the brass or go gauge, making sure the bolt is completely closed. Screw the barrel in until it stops (the lettering on the barrel should now be aligned), back off ever so slightly, and use the tool to tighten the barrel nut.

DSC00468.JPG


DSC00469.JPG


DSC00470.JPG


DSC00471.JPG


DSC00472.JPG
 
Last edited by a moderator:
RCP, I have been having the same thoughts about a heavy barrel in a 8 twist.
To be able to run the heavier Bergers, JLK's, or just stabilize my 95 gr VLD's a bit better for LR.

Rifle shoots better than me already, so a re-barrel may have to wait until it starts showing signs of wear, or my pocketbook allows. Whichever comes first.

Nice work on the removal demo, thanks !

Steve
 
Forgot to follow-up on this thread.

The threads are 1"-16 (mine measure .998"). So far no other barrels that I found would be a simple thread on installation. The M77 uses the same threads, but no barrel nut so the threaded are far too short.
 
Thanks for the write up.

With the new introduction of the Ruger American Predator, you may get your answer for a heavy barrel that will fit it. Now, whether it is the length and twist you are looking for is another story.

I for one, and looking forward to getting my hands on one in 6.5 Creedmore
 
I don't have my RAR anymore. I added the pics because I got a few PM's asking for them (this thread is pretty old).

The RAR Predators are pretty sweet, but its still a pretty light barrel.

The stocks are terrible, but the trigger is FANTASTIC. I have a Rem 700 now, the stock is WAY better, as is the factory varmint barrel, but the trigger is lacking. Good thing with the 700's is for $100 I can have a trigger in the mail whenever I want.
 
thanx for adding the pix. sounds like the only stock barrels that will fit are the RAR or RAP. when i burn out my .243win i'd probably want to replace it with an RAP 6.5 Creedmore.

fwiw, there's an easy "fix" for the RAR stock (and others) - Rockite. just mix up this cement and pour into the fore end and buttstock (put some 1" pvc pipe as a filler of sorts). the mud will harden within 15 minutes and cure overnight. it will make the fore end STIFF as steel, and the butt area will be a better balance, plus mercury or shot or whatever can be added to the tube for more recoil dampening. this adds about a pound to rifle.

the barrel is fully free floated both before and after the rockite treatment.

add in the swfa 10x and a caldwell bipod, and unloaded she's 10lb 5oz. very accurate for 3 rounds, then the light barrel needs to cool down.

woY6ssv.jpg


26WRU3f.jpg


mKf85UD.jpg
 
You must log in or register to reply here.
Back
Top