Need advise with a S&W 629 hammer

D

Doyle

New member
I just picked up a used 629. The trigger pull appears to have been lightened as the DA pull is nice and sweet and the SA pull is almost scarry light. Those are OK. What worries me though is the hammer pullback. When I thumb the hammer back, the first half of hammer travel is extremely light. Then, it's like a 2nd spring kicks in and the last half of the pullback is much more difficult. I've never before seen another hammer feel the same way.

Any ideas?
 
Sounds like someone has tried to do a trigger job by cutting a coil or two off of the rebound slide spring. I would recommend you take the pistol to a good smith or send it to S&W for service/repair.
 
Scorch,looking at the schematic I can see how that might make the hammer pull lighter (as in the first half of the hammer travel). But, how would that make the 2nd half harder than normal?

If it really is the rebound slide spring, how hard is it to get to? I'm getting to be a fair garage gunsmith for simple jobs and Numrich has the replacement spring for less than $2.00.
 
If you nip off a couple of coils, the trigger pull is reduced because the force of the spring against the trigger is reduced, and you will really feel it when the mainspring starts to flex then the rebound spring starts to get compressed. Check the strain screw on the mainspring also to make sure it is tight. If you really want to get into the guts of the pistol, open it up and take everything out, measure the length of the rebound spring and compare it to what S&W says it should be. While you have it open, you can check all the internal surfaces for burrs and varnished oil. Many times, just giving it a bath and oiling the works will smooth out the trigger.
 
The stacking/increasing resistance when cocking the hammer manually sounds to me like someone has severely bent and reshaped the orginal hammer spring. Try replacing this leaf spring with a Wolff reduced power hammer spring from Brownells and see if the problem goes away. I use this Wolff spring in all my K/L/N frame Smiths and it is great. It has slightly less strength than factory S&W hammer spring but I have not had any failures to fire in at least 8 different S&W revolvers over the last 20 years. ALWAYS keep the hammer spring tension screw in front of grip TIGHT.

To increase the trigger pull, simply replace the (probably shortened) rebound spring with one of the springs from Wolff reduced power hammer spring pack.
 
If you really want to get into the guts of the pistol, open it up and take everything out, measure the length of the rebound spring and compare it to what S&W says it should be.
Click to expand...
If the rebound spring has not been cut, the ends of the spring will have a "finish" configuration on both ends. It it has been cut, it will be obvious upon inspection.
The length of lighter after-market reduced weight springs are all the same length despite having different pull weights.
In any case, measuring the length of rebound spring will not provide any useful information.
 
It's possible you're feeling "knuckling" of the mainspring.

If the strain screw is backed out or shortened too much, the mainspring can sort of kink, or "knuckle" during cocking.

My first move would be to check the strain screw to be sure it's screwed in all the way, and to see if it looks like it's been shortened.
 
What has probably happened is that someone either screwed out the mainspring strain screw too far, or ground it off on the inside to reduce mainspring (hammer spring) tension. When you do that, the spring is too straight and when the hammer comes back part way, it comes up against the top of the mainspring, resulting in very hard cocking from that point on.

This is an indication of a "trigger job" done by an ignoramus, and likely a sign of more trouble to come. If you are lucky, you might get by with a new strain screw, but I bet you are looking at a new hammer and probably new trigger down the road.

Jim
 
Problem solved. Jim's response made me take a look under the hood and sure enough, some cork soaker had backed the main spring strain screw all the way out. I'm going to shoot it like it is for a while and see if it is smooth enough for me. If not, I'll invest in a $15 spring kit from Wolf and see what that does.

Thanks for all your help guys. This is my first S&W. I have previously been a Ruger man. The Smiths are a lot more complex.
 
You must log in or register to reply here.
Back
Top