Mossberg 590 with ghost ring sights and a heat shield???

I

IdahoG36

New member
I purchased a Mossberg 590 a while back and it came equipped with ghost ring sights. My question is this- Is there any way to modify a factory Mossberg heat shield to fit a gun with ghost ring sights? Have any of you done it? Please let me know, any suggestions are welcome.
 
It can be done, but you have to force the heatshield down over the top of the barrel instead of just sliding it over, you'll probably scratch the finish on the barrel....
 
100_0515.jpg


100_0517.jpg


This is for the 590A1 with the heavy barrel. If you have the standard 590, it will be a lot easier and you probably won't have to do any fitting.
The handguard is the Mossberg stock handguard in park finish.
To start with I had to get two slightly smaller diameter and longer machine screws and nuts. Sorry, I don't remember exactly what size. I would have written it down if I had realized how many times I was going to have give out this info. Luckily they did have some already in tactical black. Make sure that that you don't get them too narrow, you want them to stay secure and not go TU on you. You also want them to be at least two and half to three inches long so you will have enough room to work with them and to make it easier to secure the nuts without having to try to apply a lot of leverage on the forward barrel ring.
To fit the guard on the barrel, you will need to rotate it slightly to the side (9 o'clock or 3 o'clock) and hold it parallel to the barrel. Slip the rear barrel ring over the barrel (you want to do this at a point where the rear barrel ring can slip over the narrower barrel diameter as it tapers towards the muzzle) and start sliding the guard to the rear toward it's final position. You might have to rotate the barrel back towards its normal orientation and position (top dead center) on the barrel as you slide it to the rear. The forward barrel band should be slipped over the barrel as it clears the front sight assembly. You may want to put some masking tape on the barrel to prevent scratches for this step as it might be a tight fit depending on your guard and barrel.
You will have to relieve some of the metal on the underside of the forward barrel band. This is the part with the two "ears" that come down and that the cross screws secure. This piece is spot-welded to the actual body of the shield, so be careful that you don't remove too much metal. You will have to test fit the guard as you go to see how much you need to take off.
You will also have to slightly extend/enlarge the cross-screw holes in the ears to give the cross-screws enough clearance below the barrel. I'm not talking about much, just a little.
You will have to do several trial fits to make sure that you don't take to much metal off of the guard. As you are fitting it, check the clearance of the cross-screw holes when the barrel is mounted to the receiver and with the handguard in its proper position. You will need to fit the screws through the forward barrel band to make sure that you can get the nuts on them. Do not trim the length of your cross screws yet.
Once you have the guard modified so that you can get the cross screws through the forward barrel ring, take it off. Apply some cold blue, Casey's touch up, Duracoat, or whatever. You just want to apply some protection to the exposed raw metal so that you don't get any corrosion under the guard.
Trim the plastic spacer that comes with the guard as directed in the instructions. As always, trim slightly oversized so that you can make a final fit to test for proper length and fitment of the spacer. It may be necessary to remove some material from the top or bottom surface of the spacer again depending on your barrel and guard.
Once you have the guard like you want it, install the guard and secure it with the cross screws. Now you can trim the length of the screws, and touch up the raw metal ends.
You now have the rare honor of what Mossy says you can't do and I've been doing for about seven years.
 
Excellent. Thank you very much. I ordered a parkerized Mossberg heatshield yesterday, and then read on the Mossberg site that it couldn't be installed on guns with ghost ring sights. I figured since it only cost me $22, I would experiment and try to fit it. If it didn't work, I'm not out much money.
 
what m24 said. not sure if he posted them at shotgunworld but thats the way to do it. it makes a difference if you have the heavy barrel or not. easier without the heavy barrel.

be sure to take the plastic spacer and trim it then fit it to the lug.
not using the spacer and you dont have the heavy barrel the shield may slip and could cause malfunctions. had a bad day at range when I made mistake of putting the shield back on without the spacer.

love that video though prefer the M7 bayonet
 
I bought my Mossberg 590 New about 18 Months ago

Absolutlely Love It! Its the ultimate "Home Defense Weapon" when facing multy perpatrators. "Some Seriuos Shock & Awe Effect" Happens;

When I Rapid Fire All 8 or 9 Rounds in a matter of about 8 seconds :D

Stilll trying to fing a sling that I like for it?? Have tried a couple but still not found the right one for me, yet? :( The latest was the Bunjee 1 Point Sling,:(

I outfitted it with the tac-star collapasable stock, & The front Pistol Grip instead of The Standand Pump Grip. So it gives me dual pistol grips front & rear, For those times when I need to fire it from the waist postion, Much better handlling with the dual pistol grips for me.

Chris In Maine :cool:
 
You must log in or register to reply here.
Back
Top