Achieved 1330 fps with my 1858 Remington

P

phil97

Inactive
I was testing the velocities with my new batch of homemade black powder. This one is even more powerful than the last.

I shot it 3 times with a round ball and 1 with a 200 grain conical (the conical was powered by my old powder but the results are still relevant)



140 grain, .454 round ball velocities:

1: 1297 fps
2: 1261 fps
3: 1330 fps

Average Velocity: 1296 fps
Average Energy: 522 foot pounds



200 grain conical:

1: 1121

Energy: 558 foot pounds

I'm very impressed and very satisfied with these results

Video: https://www.youtube.com/watch?v=oARwYenvZ5c
 
Last edited:
Congrats! I obtained up to 1400 fps with my remmy with a RB, too, and almost 1100 with a 200 grns conical. Both with my homemade powder. Which wood are you using for charcoal? I found that depending on the density of each charcoal, quantities into the recipe must be changed. I. E. For a willow charcoal is possible to get a good powder with a 15% charcoal, but in case of using harder woods may be necessary to go up to 25 or even 30% of charcoal. And I never use more than 5% of sulfur as modern primers could ignite such powder anyway.
 
It is important to tell that for all mentioned proportions I was talking of percentage to obtain a 100% of powder, by weight. So when I make a powder with a denser wood I tend to use (I. E. to get 100 grams of powder), 30 grams charcoal, 65 saltpeter and 5 sulfur.
 
Centurion, that is actually very interesting. I use grapevine charcoal. I was actually wondering if decreasing my sulfur percentage and increasing the charcoal would give me a bigger boom (as it would mean having more fuel in the mix, sulfur is only for lowering ignition temperature). Seems like my suspicions were confirmed. Now that you told me that I'll absolutely have to try it out when I make a new batch
 
Sulfur is as you say, used to lowering the ignition temperature, and saltpeter is an oxidizer, wich helps oxygen to burn the charcoal. But 60 or 65 percent of it is all you need for such task in case your charcoal is very dense. If not, just decrease the amount of sulfur and try increasing charcoal by 10%. I. E. 25 grams charcoal, 5 sulfur and 70 saltpeter. Try making 100 grams for the first time and let us know your findings.
 
Experimentation is the only way to find wich could be the best homemade gunpowder you are able to obtain with the ingredients at hand. My suggestions are based on my findings after experimenting with some very dense charcoal made of hard woods.
 
72 grains of homemade black by volume. There's still only about 40 grains worth of powder in the chamber (homemade bp is not very dense)
 
I’m at a loss here. 72 grns “volume” wouldn’t fit in a NMA chamber. Is it 40 grns volume that weighs 72 grns? Is this a 3F or 4F powder?
 
No, it's the opposite. 72 grains by volume. It fits because it's highly compressible. I fill the chamber up, ram it down, then fill it up one more time. It's also not very dense, which means I'm not overcharging the gun
 
Not me. But I use to mill it for at least 3 hours (in my lead balls mill), and after that I mix it with jelly alcohol. When almost dry I screen it and let dry.
 
No, I don't use dextrin if that's what you're asking. I grind each ingredient separately in a coffee beans grinder to avoid any explosions. I grind for 30 seconds each. Then I mix it all with isopropyl alcohol and stir and mix for about 1 hour as the alcohol evaporates. When it stops being a liquid and turns into sort of a paste, I push it through a mesh screen and leave it to dry for a few days
 
Dextrin. Ah. That is what i meant.
Thanks to you both for your responses. It is helpful to know that you both use alcohol. I have not tried that.
How much liquid alcohol do you use to process 100 grams of mixture?
How fine is the mesh that you use?
I am asking because I have never been satisfied with my own BP product and want to try a different method.
Pete
 
Last edited:
Good morning! As far as I can see from both recipes, alcohol is not the most important part of the mixture. Both powders are highly energetic and the colleague uses isopropyl alcohol and I use jelly, which is made with water, glycerin and ethyl alcohol.

By the way, I use to add enough jelly to form a liquid compund...maybe 100 grams of alcohol per same quantity of powder.

And at last but not least, I 'm using a metal mesh of about 0.5 milimeters.

Anyway, I'm totally convinced that the most important ingredient is charcoal. Which wood are you using to make yours?

Regards!
 

Attachments

  • Homemade powder.jpg
    Homemade powder.jpg
    344.4 KB · Views: 29
Last edited:
I also use enough alcohol to turn it into a liquid. I found that having enough alcohol to dissolve the particles makes them become more intimately mixed with each others and burn better. I'll attach some pics of my bp for you to see the grain size
 

Attachments

  • image0.jpeg
    image0.jpeg
    69 KB · Views: 28
  • image1.jpeg
    image1.jpeg
    182.8 KB · Views: 25
It is very much like mine! Did you see the picture I attached to my past posting? I'm attaching another one.

By the way, I also make my own primers, so do you?
 

Attachments

  • Primer.jpg
    Primer.jpg
    646.4 KB · Views: 27
  • Powder.jpg
    Powder.jpg
    530.3 KB · Views: 31
Last edited:
They do look similar! They're both greyish in color too. The commercial bp I bought is black, I heard it's coated in graphite for some reason. I don't make my own primers but I've seen some videos of people making them and it doesn't seem hard. It may be useful for a time when percussion caps get banned or when they become available only to license holders. So far here in Europe bp guns are mostly unregulated, which surprised me when I found out a few years ago. I just had to buy one!
 
You must log in or register to reply here.
Back
Top