1911 recoil spring

A

ammo.crafter

New member
Shooting a Colt Series 80 45acp for PPC competition and need a replacement recoil/slide spring.
What weight spring would you use for a 200gr cast lead SWC at approx. 825f/s?
 
That's the load a lot of USPSA competitors use.
It's one that doesn't seem to be all that picky concerning recoil springs.
Springs from 14 to 18 lbs can apparently be used, depending as to how the gun feels to the person using it.
 
I always use the Wolff 16.5 lbs variable rate spring.
Click to expand...

Yep, that's been my choice for years, set all my full size 1911 style guns up with a 16.5 variable.

When I was shooting USPSA the trend was to go with as light of recoil spring as possible, I would say a 14 lb spring would be just fine.

If I remember correctly I believe the original recoil spring in the 1911 would have been rated at 14lbs, however back then I don't believe they rated the springs in pounds.

Best Regards
Bob Hunter
www.huntercustoms.com
 
For 200@825 you can certainly use a 14# spring.
I know guys using 12# springs with 200@850 loads, and while the guns run, I think they do it more for tuning the recoil characteristics than any other consideration. I use a 14# for 200@850, mostly so I don't have to change springs if I want to shoot full-power loads.
 
Actually it's done for reliability and to keep the gun from beating itself to death. You want the heaviest spring (for the bullet / powder combo) that still allows the pistol to function without an malfunction. I used a 16# spring for 200 gr. SWC at between 750 and 850 FPS without a com. With a comp I used either a 8 or 9 # spring. Every pistol is different and what runs well in one doesn't always run in others. I know people the use 18 # springs in stock guns with full power loads and people that use 4 # springs in all-out race guns.

I'm reasonably sure a 16 # would function properly for the OPs loads.
 
You want the heaviest spring (for the bullet / powder combo) that still allows the pistol to function without an malfunction.
Click to expand...

I lean more toward the lightest spring that will run reliably. The heaviest spring that still runs is right on the edge of a failure to eject, because you are slowing the slide at the point that you need some energy to kick-out the empty case. Does PPC allow mulligans for functional failures?
A 1911/.45 should feed with a 12# spring, so there's no need to use a heavy spring for feeding; some consider the 1911 recoil spring to be a "feed spring".
 
Spring

Actually it's done for reliability and to keep the gun from beating itself to death.
Click to expand...

*cough*

A few years back, I arranged a demonstration for a guy who believed that he needed a 22 pound spring to keep his LW Commander from beating itself to death.

I fired my LW Commander 98 times with factory hardball without a recoil spring, field-stripping the pistol every 49 rounds to show him that the impact abutment in the frame was undamaged. Still not convinced, he handed me a magazine full of +P. Still no damage.

He stormed off, claiming that I'd set up a super special pistol that I could do it with.

*sigh*

Many IDPA/USPSA shooters fire their guns tens of thousands of rounds year in and year out with 12 pound springs without issue.

If you want to reproduce my demo, use a FLGR and plug. The standard "stub" type guide rod will get cattywampus and tie up the slide...possibly damaging something. Be sure to check to see that the bushing is line up correctly between shots if the end of the rod doesn't come out flush with the bushing.

some consider the 1911 recoil spring to be a "feed spring".
Click to expand...

That's exactly what it is...an action spring...just like the action spring on an M1 or M14 rifle. Its function is returning the bolt/slide to battery. Whatever else it does is incidental.
 
RickB we're looking for the same thing just attacking it from the opposite ends of the spectrum. I start heavy and work down. It's the spring that works reliably we are both looking for. :)

I'm pretty sure there aren't any Mulligans. :eek:
 
1911Tuner, sorry to tell you that over the life of the gun a too light a spring will cause damage. I've see the cracked frames to backup my "opinion". I have a Kimber Custom (that's the cheep one) that I used / use for competition that has over 70,000 rounds through it and no damage. I've seen 1911s with far fewer rounds with cracked frames because of too light a spring.

Put 20,000 or 30,000 rounds through your 1911 without a recoil spring then come back and tell me there was no damage and I'll gladly eat my dish of crow. ;)

Now if someone wants to run a 12 # spring and + Ps that's their prerogative. Mine gets beat up less and functioned perfectly with a 16 # spring. I do agree that 22 # is overkill and probably would cause FTF with standard ammo.
 
re:

1911Tuner, sorry to tell you that over the life of the gun a too light a spring will cause damage. I've see the cracked frames to backup my "opinion"
Click to expand...

You probably won't wanna hear this...but here goes.

The cracks at the junction of the rails and impact abutment are the result of thin cross-sections and sharp corners. They're self-limiting and in no way affect the function of the gun...and they're inevitable if you shoot enough...regardless of the spring rate.

They'll even crack if shock buffs are used for all shooting. It'll just take a little longer. Nature of the beast, I'm afraid.

I have a pair of early Colt 1991A1s that I bought in October '91 and January '92 strictly for beater duty. They're nearly at the 400,000 round mark...collectively...about evenly split. They both cracked in those areas many years and many tens of thousands of rounds ago. The cracks haven't traveled, and the pistols function just fine. I expect they'll be walkin' the walk long after I'm gone.
 
re:

Not having tried it, what's the feeling of shooting a 1911 with no recoil spring?
Click to expand...

Surprisingly soft recoil...with a little delay. About 90% of what we recognize as recoil...muzzle flip...comes when the slide hits the frame. The rest comes from the "recoil" spring itself when it creates a separate action/reaction event between the slide and frame, with the spring as the driving/accelerating force.

With an autopistol, the slide and barrel assembly is the gun. The frame is little more than the gun mount, with no solid connection between the gun and the mount.
 
.45 ACP cartridge generates say 19000 psi,the recoil spring compresses at
12 to 20 lbs.Logic says that it can not be a factor in recoil shock control.
 
Springy stuff

What many people don't know is that the original spring...the one that John Browning and Colt's dream team settled on...wasn't rated in pounds. The specs were 32 and 3/4 turns of .043 diameter music wire. Compared to Wolff's 32-turn/14 pound spring...that works out to about 14.5 pounds at full compression, and 13.5-13.7 pounds at full slide travel as installed in the gun.

This, with the old, soft frames and slides and original USGI spec hardball ammunition.

The spring's specs were changed at some point prior to WW2, and they became 30 turns of .044 diameter music wire...which resulted in pretty much the same dynamics.

And until the introduction of "Heavy Duty" springs, those were pretty much the only springs that were available...either through military surplus, or from Colt.

And the frames held up well into the 1980s when they were phased out.

Too much emphasis on the frame and not enough on the slide. The slide and barrel assembly catches all the hell. That's why the military ordered about a dozen of'em for every finished pistol that was delivered.
 
^^^ I agree. I run a 10lb spring in my 45cal 1911 open gun and an 8lb spring in my 9mm 1911 stock gun. The key to to gun functioning with light springs is to polish and smooth out every thing the cartridge has to touch on the way into the chamber.

John
 
re:

I run a 10lb spring in my 45cal 1911 open gun and an 8lb spring in my 9mm 1911 stock gun.
Click to expand...

Yup. Consider the IDPA/USPSA shooters who run 12-pound springs in their stock .45s and shoot tens of thousands of rounds of major PF ammo a year...year in and year out...without buffs. Some of'em don't change their springs until the return to battery gets sluggish. One local guy changes springs every 50,000 rounds whether the gun needs it or not.

And their frames are fine.
 
It probably doesn't matter much, but current Major Power Factor for USPSA and CDP Power Floor for IDPA is 165, only 718+ fps if you stick with a 230 gr bullet, or more likely a 200 at 825+.
That is only 87% of factory, allowing a little safety margin of 170 on match power factor.
 
You must log in or register to reply here.
Back
Top