# 1 reticle Muzzle loader scope?
- Thread starter BerdanSS
- Start date
Pahoo
Thanks I'll check that site out, not wanting a red dot.
SSA
I think I was looking at those this morning...but at the one with the circle dot.
Will any rifle scope work? or does it HAVE to be for a muzzle-loader. I would think the shock would be less on a ML than say a .300 win mag.
Thanks I'll check that site out, not wanting a red dot.
SSA
I think I was looking at those this morning...but at the one with the circle dot.
Will any rifle scope work? or does it HAVE to be for a muzzle-loader. I would think the shock would be less on a ML than say a .300 win mag.
Any good rifle scope will work. Almost all the low-powered scopes available have a duplex, or some sort of a ballistic compensating reticle, or take batteries.
Leupold makes the 1-4 or 2-7 with half a dozen different reticles. Turkey plex, pig plex, sabre, wide duplex. There are probably a dozen more available from the custom shop.
Leupold makes the 1-4 or 2-7 with half a dozen different reticles. Turkey plex, pig plex, sabre, wide duplex. There are probably a dozen more available from the custom shop.
DNZ Game Reaper Mount?
I've narrowed it down to four. Nikon 3x32 BCD, Millett 1-4x24 DMS, Leupold 1-4x20 VX-1, or a Burris fullfield tactical 1-4x24.
I also found this nice, solid looking scope mount made by DNZ.
Anyone use one of these? thoughts? This is made specifically for CVA inlines older than 2009. Looks solid, I know it will obstruct the top of the breech plug for primer removal, but I can still get it out the side.
I've narrowed it down to four. Nikon 3x32 BCD, Millett 1-4x24 DMS, Leupold 1-4x20 VX-1, or a Burris fullfield tactical 1-4x24.
I also found this nice, solid looking scope mount made by DNZ.
Anyone use one of these? thoughts? This is made specifically for CVA inlines older than 2009. Looks solid, I know it will obstruct the top of the breech plug for primer removal, but I can still get it out the side.
Last edited:
Well after doing a mock up of the reaper mount with an extra PRI rail section I had....I fount it to be a complete PITA to remove a primer with a one piece base/ring setup. And as SSA said, I believe the scope I decided on wouldn't fit in the mount.
So I opted for the Durasight Z2s. They are two solid bolt on ring/mounts for a 1" tube and were made for the CVA. They'er pretty nice and well made for $25. And they match the color I did on the barrel to boot.
So I opted for the Durasight Z2s. They are two solid bolt on ring/mounts for a 1" tube and were made for the CVA. They'er pretty nice and well made for $25. And they match the color I did on the barrel to boot.
bamaranger
New member
Leupold
I bought a used Leupold 1-4x shotgun scope off ebay, (Vari x II) and shipped that rascal off to Leupold. For $55 bucks they put a genuine German #1, that big funky 3 post reticle, in it. I had it back inside 2 weeks.
For quick and close, out to about 150 yds on deer, and in bad light, it works very well. You will see a non illuminated #1 , in bad light, better than any other non illuminated reticle on the market, I am quite certain.
It would be ideal if one were wanting to scope a turkey gun also.
I bought a used Leupold 1-4x shotgun scope off ebay, (Vari x II) and shipped that rascal off to Leupold. For $55 bucks they put a genuine German #1, that big funky 3 post reticle, in it. I had it back inside 2 weeks.
For quick and close, out to about 150 yds on deer, and in bad light, it works very well. You will see a non illuminated #1 , in bad light, better than any other non illuminated reticle on the market, I am quite certain.
It would be ideal if one were wanting to scope a turkey gun also.